.jpg)
.jpg)
I - Routine maintenance
1 - Check the entire cap screws screwed to the department, the links, the details, the wire first. Building started paying special attention to wheel trailers cakes, battery racks
2 - Check the coolant machine, check fuel level, ensure adequate lubrication, no leakage flow
3 - Check the electrical system, the battery began to rack tightly, the start beheading foam battery, battery fluid levels and cut down battery injustice
4 - Start the machine, check the tightness of vacuum priming pumps for special attention tam.dac machine lubrication as vacuum pumps for M800 LX
5 - Check the fire fighting equipment fitted under pump
II - Maintenance work after 50h pumps
1 - Remove the air filter to clean, change the oil sands te.dong gasoline lock and remove the fuel filter cup carburetor to wash, rinse residue in fuel tanks
2 - Tighten the lid screws to the prescribed level
3 - Check the status of drive clutch springs (for PO3 machine; P05; poland and trailer pumps)
4 - Check the tightening of the screws start block machines with optical tweezers machine bed
5 - Check the tire of the wheel 2 (pumps trailer)
6 - Check the voltage for each cell must be greater than 1.7 volts required for additional load
7 - Check the contact gap adjustment, cleaning of these connectors (screw pads platinum)
8 - Remove the ignition candles, clean the ignition pin, pin adjustment of the ignition slot and check the working of the ignition candles
9 - Check the grip of centrifugal pumps and the working of the other valve
10 - Let the pump working, check the tightness of the pump, sprinkler and ability hut
III - Maintenance of the pump after 200 hours of work:
1 - Check and adjust valve clearances pump Rubber feet 4 times, check the technical status piston group, cylinder pump 2 times
2 - Check the cylinder compression ratio in the engine
3 - Remove the carburetor to wash, blow paths through gasoline dropped buoys
4 - Check the tightness of the fuel supply system. fuel tank, if necessary, removed rinsed
5 - Replace with new oil pumps 4 times
6 - Check the cooling water tanks, if the phenomenon of leakage flow must overcome in time
7 - Remove the battery to wipe the outside, through the vent check the voltage of the compartment, need for additional charge
8 - Check the status and the work of candles ignition, if necessary, replace the ignition candles New
9 - Check and clean and adjust contacts (screw pads platinum), the status of the ignition coil
10. Check the ability to work the rope line vacuum pumps for priming centrifugal pump and the ability to work of centrifugal pumps
IV - Inspection - Maintenance - Replacement
1. Check
- Leaking oil, lubricant, coolant
- Parameter clock and safety systems.
- Check the pressure viscosity.
- Check strange noises.
- Check intake air system.
- Check the exhaust system.
- Check the vent pipe.
- Check the belt tension.
- Check the status of the propeller.
- Check the hard piping, hoses, joints.
- Check the air filter system
- Check damaged, cracked or twisted belt
- Check the status of the propeller.
- Check the status of the radiator.
2. Maintenance
- Corn soup gap adjustment & nozzles.
- Check and repair of motor protection system.
- Apply grease tensioner wheel alignment, engine parts apart.
- Check and replace the damaged pipe.
- Tighten or replace the broken bolt.
- Making the pot, instead of silver, instead of phosphate, making the cylinder, piston
- Cleaning, calibration, vacuum parts
- Clean, balancing fuel supply parts
- Clean, viscosity calibration pump parts
- Clean Wind calibration unit
- Check the electrical system connection, if broken
- Check the whole pump
- Take apart, clean and inspect the inside; If discovered details will repair damaged or replaced.
3. Replace
- Replace the oil filter
- Replace the fuel filter
- Replace motor oil
- Replace the air filter
- Replace the gear
Hotline: Mr Hải 0901.586114 VP: 0312638155
Email: hkdjsc@gmail.com
Website: hkdjsc.com.vn; pccchaiphong.vn; pccchaiphong.com; pccchaiphong.net
